<?xml version="1.0" encoding="UTF-8"?>
<!-- edited with XML Spy v4.0 (http://www.xmlspy.com) (SISCO/Engineering) -->

<!-- ****************************************************************** -->
<!-- * SISCO MODULE HEADER ******************************************** -->
<!-- ****************************************************************** -->
<!-- *   (c) Copyright Systems Integration Specialists Company, Inc.,   -->
<!-- *                      2001 - 2004, All Rights Reserved            -->
<!-- *                                                                  -->
<!-- * MODULE NAME : osicfg.xml                                         -->
<!-- * PRODUCT(S)  : MMSEASE-Lite                                       -->
<!-- *                                                                  -->
<!-- * MODULE DESCRIPTION :  Configuration File for Lean-T Stack        -->
<!-- *                                                                  -->
<!-- *  This file is used to set the log masks used to control          -->
<!-- *  logging performed by the MMS-EASE Lite Debug Libraries,         -->
<!-- *  as well as to set memory debug flags. This module is            -->
<!-- *  read by the source module 'osicfgx.c'.                          -->
<!-- *                                                                  -->
<!-- *  MODULE DESCRIPTION :                                            -->
<!-- *                                                                  -->                                                                           
<!-- *  Configuration file for Lean-T Stack                             -->
<!-- *                                                                  --> 
<!-- *  The configuration file has three sections.                      -->
<!-- *  The order of sections in the configuration file is relevant:	-->
<!-- *                                                                  -->  
<!-- *  Network                                                         -->			
<!-- *                                                                  --> 					
<!-- *  Transport     This section may be empty (default parameters	-->
<!-- *                will be used).					-->
<!-- *                                                                  -->  
<!-- *  Addressing    This section should be present to                 -->
<!-- *      	      properly terminate parsing of cfg file.		-->
<!-- *                                                                  --> 
<!-- *  Note:  Most parameters are optional unless stated that          -->
<!-- *         they are mandatory.  If an optional parameter is         -->
<!-- *         not configured in this file a default value will         -->
<!-- *         be used.                                                 -->
<!-- *                                                                  -->  
<!-- * MODIFICATION LOG :                                               -->
<!-- *  Date     Who   Rev  Comments                                    -->
<!-- * =======  =====  === ==========================                   -->
<!-- * 01/27/04  ASK    04  Commented out DTD and Schema references     -->
<!-- * 01/15/04  EJV    03  Added Rfc1006_Max_Spdu_Outstanding          -->
<!-- * 11/05/01  GLB    02  Added MMS section                           -->
<!-- * 08/31/00  GLB    01  Module created from existing lean.cfg       --> 
<!-- ****************************************************************** -->
<!--
#############################################################################
#  NOTE:  Descriptions of parameters are at the bottom of this module. 
###########################################################################-->

<!-- Uncomment to use DTD / Schema 
<!DOCTYPE STACK_CFG SYSTEM "..\osicfg.dtd">
<STACK_CFG xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="..\osicfg.xsd">
-->

<STACK_CFG>
	<MMS>
		<Max_Mms_Pdu_Length>32000</Max_Mms_Pdu_Length>
		<Max_Calling_Connections>4</Max_Calling_Connections>
		<Max_Called_Connections>0</Max_Called_Connections>
	</MMS>
	<Network>
		<Clnp>
			<Lifetime>50</Lifetime>
			<Lifetime_Decrement>1</Lifetime_Decrement>
			<Cfg_Timer>120</Cfg_Timer>
			<Esh_Delay>5</Esh_Delay>
			<Local_NSAP>49 00 01 53 49 53 43 09 01 01</Local_NSAP>
		</Clnp>
	</Network>
	<Transport>
		<Tp4>
			<Max_Tpdu_Length>1024</Max_Tpdu_Length>
			<Max_Remote_Cdt>4</Max_Remote_Cdt>
			<Local_Cdt>4</Local_Cdt>
			<Max_Num_Connections>8</Max_Num_Connections>
			<Max_Spdu_Outstanding>4</Max_Spdu_Outstanding>
			<Window_Time>10</Window_Time>
			<Inactivity_Time>120</Inactivity_Time>
			<Retransmission_Time>10</Retransmission_Time>
			<Max_Transmissions>2</Max_Transmissions>
			<Ak_Delay>2</Ak_Delay>
		</Tp4>
		<Tcp>
			<Rfc1006_Max_Tpdu_Len>1024</Rfc1006_Max_Tpdu_Len>
			<Rfc1006_Max_Num_Conns>8</Rfc1006_Max_Num_Conns>
			<Rfc1006_Max_Spdu_Outstanding>50</Rfc1006_Max_Spdu_Outstanding>
		</Tcp>
	</Transport>
	<NetworkAddressing>
		<LocalAddressList>
			<LocalAddress>
				<AR_Name>local1</AR_Name>
				<AP_Title>1 3 9999 33</AP_Title>
				<AE_Qualifier>33</AE_Qualifier>
				<Psel>00 00 00 01</Psel>
				<Ssel>00 01</Ssel>
				<Tsel>00 01</Tsel>
				<TransportType>TCP</TransportType>
				<!-- TP4 or TCP or TPX -->
			</LocalAddress>
			<LocalAddress>
				<AR_Name>local1cl</AR_Name>
				<AP_Title>1 3 9999 33</AP_Title>
				<AE_Qualifier>33</AE_Qualifier>
				<Psel>00 00 00 02 </Psel>
				<Ssel>00 01</Ssel>
				<Tsel>00 01</Tsel>
				<TransportType>TCP</TransportType>
				<!-- TP4 or TCP or TPX -->
			</LocalAddress>
		</LocalAddressList>
		<RemoteAddressList>
			<RemoteAddress>
				<AR_Name>remote1</AR_Name>
				<AP_Title>1 3 9999 23</AP_Title>
				<AE_Qualifier>23</AE_Qualifier>
				<Psel>00 00 00 01</Psel>
				<Ssel>00 01</Ssel>
				<Tsel>00 01</Tsel>
				<NetAddr Type="IPADDR">127.0.0.1</NetAddr>
			        <!-- EXAMPLE:  <NetAddr Type="IPADDR">208.176.40.52</NetAddr> -->
				<!-- EXAMPLE:  <NetAddr Type="NSAP">49 00 01 53 49 53 43 44 02 01</NetAddr> -->
			</RemoteAddress>
		</RemoteAddressList>
	</NetworkAddressing>
</STACK_CFG>
<!--
#############################################################################
#
#  Description of NETWORK parameters 
#
#				CLNP Only Parameters:
#				======================
#   
#   Lifetime	
#				Valid range is from 1 to 255 (in 500 ms units).
#
#   Lifetime_Decrement	
#				Valid range is from 1 to 255 (in 500 ms units).
#
#   Cfg_Timer        The Configuration Timer specifies how 
#                               often ESH will be sent.
#				Valid range is from 0 to 32767 (seconds).
#				Note that the Holding Time in ESH sent
#				is set to 2*CfgTimer.
#				If Cfg_Timer=0 then ESH will not be sent.
#  
#   Esh_Delay	Delay time before first ESH is sent.
#				Valid range is from 0 to 32767 (seconds).
#
#               COMMON Parameters:
#               ===================               
#
#   Local_MAC	Local MAC address (up to 6 hex bytes
#				separated by spaces).
#				For the ADLC sub-network the local MAC is
#				a required parameter and it has to match
#				the address in the adlc.cfg file!
# 				For ADLC sub-network the MAC address is a
#				USHORT number (2 hex bytes swapped,
#				example: 30 00 hex swapped = 48 decimal).
#               For the Ethernet this param will be read
#				from the driver during initialization
#				(any value from config file will be ignored).
#
#   Local_NSAP	Local NSAP (up to 20 hex bytes separated
#				by spaces, example: 49 00 11 11).
#				This is mandatory parameter.
#
#############################################################################
#
#  Description of TRANSPORT parameters 
#
#				TP4 Only Parameters:
#				====================
#
#   Max_Tpdu_Length	 	
#                               Max length of TPDU. Base on SNPDU size.
#				Valid values are: 128, 256, 512, 1024,
#				2048, 4096, 8192.
#
#   Max_Remote_Cdt		
#                               Max credits we can handle.
#			        Will allocate this many TPDU_DT structures.
#			        Valid values are: 2, 4, 8, 16.
#			        CRITICAL: MUST BE POWER OF 2.
#
#   Local_Cdt          Credit value we will ALWAYS send in ACK.
#			        We only accept in-sequence TPDUs so only
#			        purpose of this is to allow peer to send
#			        ahead.
#			        Valid range is from 1 to 15.
#
#   Max_Num_Connections 	
#                               Max number of connections.
#				Valid range is from 1 to 255.
#
#   Max_Spdu_Outstanding	
#                               Max num of SPDUs outstanding per connection.
#				Will allocate this many SPDU_INFO structs
#				for transmit queue.
#				Valid values are: 2, 4, 8, 16.
#				CRITICAL: MUST BE POWER OF 2.
#
#   Max_Spdu_Length	  	
#                               Max SPDU length.
#				Should be based on max ACSE msg size.
#				Valid range is from 1 to 65535.
#
#   Window_Time			
#                               Indicates the maximum time that the
#                               transport will wait before retransmitting 
#                               up-to-date window information. 
#                               Valid range is from 1 to 255 (seconds).
#
#   Inactivity_Time		
#               
#				Valid range is from 1 to 255 (seconds).
#
#   Retransmission_Time		
#                                Indicates the maximum time the transport 
#                                will wait for acknowledgement before 
#                                retransmitting a TPDU.
#				Valid range is from 1 to 255 (seconds).
#
#   Max_Transmissions		
#                               Max number transmissions of a TPDU.
#				Valid range is from 1 to 255.
#
#   Ak_delay           The TP4 skips some service cycles before
#				sending the transport ACK, to allow
#				concatination with DATA packet.
#				The recommended value for this parameter is 2.
#
#				TCP (RFC1006) only parameters:
#				==============================
#
#   rfc1006_Max_Tpdu_Length 	
#                               Max length of TPDU.
#				Valid values are: 128, 256, 512, 1024,
#				2048, 4096, 8192 and 65531
#
#   rfc1006_Max_Num_Connections 
#                               Max number of connections.
#				Valid range is from 1 to 255.
#
#   rfc1006_Max_Spdu_Outstanding	
#                               Max num of SPDUs that can be queued in gensock2.
#
#############################################################################
#
#  Description of ADDRESSING parameters 
#  Parameters for local and remote Directory Information Base (DIB) 
#
#   Common_Name	Is an alias for the P-Address. It may be up
#				        to 64 characters long.
#
#   AP-Title		Is an array of up to 16 SHORT decimal integers.
#                       The first value should be 1 (ISO)(valid range 0-2).
#                       The second value should be 1, 2 or 3 (valid range 0-39).
#                       The third value is open for assignment (If you addressing is 
#                       local this value should be 9999, the rest of the values are
#                       arbitrary.
#
#                       This is an Object Identifier assigned by the 
#                       network naming authority, representing the 
#                       Application Process Title for your particular
#                       application process.
#
#   AE-Qualifier	Is a LONG decimal integer.
#
#                       This is an optional integer value used to qualify the 
#                       Application Entity.
#
#   Psel		Up to 16 (octets) characters of ASCII encoded hex.
#
#                       This octet string represents the Presentation Selector
#                       used to identify a Presentation SAP.
#
#   Ssel		Up to 16 (octets) characters of ASCII encoded hex.
#
#                       The octet string represents the Session Selector used
#                       to identify a Session SAP that can be up to 16 octets in length.
#
#   Tsel		Up to 32 (octets) characters of ASCII encoded hex.
#
#                       The octet string represents the Transport Selector used
#                       to identify a Transport SAP that can be up to 16 octets in length.
#                       
#
#   Transport	TP4 - for Transport Class 4
#				TCP - for Transport Class 0 (RFC1006)
#
#				TP4 only parameters:
#				====================
#   NSAP	    Up to 20 characters of ASCII encoded hex
#				TP4 only, in remote_begin section(s)
#
#				TCP (RFC1006) only parameters:
#				==============================
#   IPADDR	    IP address or alias name defined in hosts
#				file for given IP address.
#				Only in remote_begin section(s)
#
##############################################################################
-->
